Vehicle-Carrying Trailers - Custom Trailer Builder

For several years now, car trailers have become one of our most popular products. We provide trailers that can suit most vehicles, be it a show car or race car, a 4-wheel drive (4WD) vehicle or anything equally large that you want to be moved for your personal or business needs.

The most standard car trailer is limited to a gross trailer mass (ATM) of 2,000 kilograms but can go as high as 2,800 or 3 200 kilograms without cutting into your trailer width.

All these categories are made with different components so that we stay in compliance with Australian federal standards.

What to Know About Vehicle -carrying Trailers

The most important thing to consider when buying a car trailer is the weight capacity. Our standard range of car trailers is rated at an ATM of 2,000 kilograms. Because most cars are getting heavier, it’s important that you buy the correct trailer that can support so much mass.

The trailer’s deck size can also be changed to suit your needs, but the bigger you go, the heavier your trailer will be. You’ll have to reduce your load weight in order to stay below the 2,000 kg ATM limit.

Our standard Car Trailer range is listed below and is in stock at all times.

14ft X 6ft 6″ Car Trailers With Rails

This trailer comes with a full floor design and a good-sized deck for loading your cargo. This trailer comes with such standard features as a full RHS chassis and drawbar, a checker plate floor with mudguards, mechanical disc brakes, side and front railings for extra strength, tie downs, slide-under ramps, front and rear tie points, seven leaf springs, 45mm solid square axles with Ford bearings and 12-volt LED lights.

You can also request a larger deck size and a winch to be installed.

Other NSW Locations We Service

We supply our car carrying trailers not only in Campbelltown but also across Central Coast, Gosford, Newcastle, Wollongong, Nowra, Port Macquarie, and other nearby areas.

14ft X 6ft 6″ Car Trailers With a Flat Deck Beaver Tail

Our most popular car trailer comes with the same good-sized deck but doesn’t require rails along the top, thanks to its upgraded chassis. This is a popular choice for vehicles with low ground clearance because of its 4-inch rear beaver tail.

This car trailer includes such standard features as an extra-strong RHS chassis and drawbar, a checker plate floor with mudguards, a rear beaver tail with a 4-inch drop, mechanical disc brakes, slide-under ramps, front and rear tie points, seven leaf springs, 45mm solid square axles with Ford bearings and 12-volt LED lights.

You can also request a larger deck size and a winch to be installed.

Tie Downs

Our trailers have standard tie-downs in the front side and rear sections, though we can install more depending on your needs. Have you considered a perforated floor? The new craze makes tying down your cars easier and faster.

Custom Car & Plant Trailers

Are you looking for something bigger? Or smaller? No matter how heavy your load might be, we can build trailers with a higher ATM. From the standard 2000kg ATMm, you can upgrade to 2,500kg, 2,800kg, 3,200kg, and 3,500kg up to a maximum mass of 4,500 kilograms.

Our trailers can be made to suit your particular car or machine. Just ask one of our friendly representatives about how to get started.

See more examples of our custom plant and car trailers in our custom trailer gallery.

Bike Trailers

Our motorbike trailers are designed as a standard 3-bike, open-air carrier. These high-performance trailers include such standard features as a full checker plate floor with 150mm-wide channels, five-leaf slipper springs, 2 Jerry can holders, a loading ramp and tie points welded to the floor.

Enclosed 2-bike trailers are also available but not kept on site. They can, of course, be made to order.

Below are some examples of our previous custom-made enclosed bike trailers.

Buy 100% Australian Made! Over 25 Years in the Industry!

To find out more about our range of vehicle-carrying trailers, reach out to us on (02) 4627 6833.